Differences

This shows you the differences between two versions of the page.

--- klipper_faq:flash_guide:rp2040:fly-adxl345-usb [2024/01/22 21:17] – removed - external edit (Unknown date) 127.0.0.1
+++ klipper_faq:flash_guide:rp2040:fly-adxl345-usb [2024/01/22 21:18] (current) – ↷ Page moved from klipper_faq:flash_guide:stm32g0b1:fly-adxl345-usb to klipper_faq:flash_guide:rp2040:fly-adxl345-usb dominik
@@ Line 1: / Line 1: @@
+====== Fly-ADXL345-USB ======
+===== Klipper flashen =====
+  * ''cd ~/klipper''
+  * ''make menuconfig'' \\ <code>
+[*] Enable extra low-level configuration options
+    Micro-controller Architecture (Raspberry Pi RP2040)  --->
+    Bootloader offset (No bootloader)  --->
+    Flash chip (W25Q080 with CLKDIV 2)  --->
+    Communication interface (USB)  --->
+    USB ids  --->
+()  GPIO pins to set at micro-controller startup
+</code>
+    * Mit ''Q'' und dann ''Y'' beenden
+  * ''make clean && make -j4''
+  * {{:klipper_faq:flash_guide:stm32g0b1:pasted:20240122-202252.png}} \\ Die Taste **gedrückt halten (!)** und den USB-C Stecker anschließen.
+  * ''dmesg'' im Terminal eingeben \\ <code>[126509.556147] usb 1-1.4: new full-speed USB device number 13 using dwc_otg
+[126509.688730] usb 1-1.4: New USB device found, idVendor=2e8a, idProduct=0003, bcdDevice= 1.00
+[126509.688767] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
+[126509.688783] usb 1-1.4: Product: RP2 Boot
+[126509.688795] usb 1-1.4: Manufacturer: Raspberry Pi
+[126509.688807] usb 1-1.4: SerialNumber: E0C9125B0D9B
+[126509.689785] usb-storage 1-1.4:1.0: USB Mass Storage device detected
+[126509.690375] scsi host0: usb-storage 1-1.4:1.0
+[126510.727183] scsi 0:0:0:0: Direct-Access     RPI      RP2              3    PQ: 0 ANSI: 2
+[126510.727877] sd 0:0:0:0: Attached scsi generic sg0 type 0
+[126510.728901] sd 0:0:0:0: [sda] 262144 512-byte logical blocks: (134 MB/128 MiB)
+[126510.729746] sd 0:0:0:0: [sda] Write Protect is off
+[126510.729766] sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
+[126510.730619] sd 0:0:0:0: [sda] No Caching mode page found
+[126510.730636] sd 0:0:0:0: [sda] Assuming drive cache: write through
+[126510.744971]  sda: sda1
+[126510.746027] sd 0:0:0:0: [sda] Attached SCSI removable disk
+</code> Es muss sowas am Ende stehen ... **Product: RP2 Boot**, **Manufacturer: Raspberry Pi**
+  * ''make flash FLASH_DEVICE=2e8a:0003''
+  * Eigentlich muss sich das Ding dann schon mit Klipper melden ... \\ ''ls -lR /dev/ | grep -v '\%%->%%\s../tty' | grep -e 'tty%%[[:%%alpha%%:]]%%' -e serial'' \\ <code>
+/dev/serial:
+/dev/serial/by-id:
+lrwxrwxrwx 1 root root 13 Jan 22 20:26 usb-Klipper_rp2040_E66138935F3C6B28-if00 -> ../../ttyACM0
+/dev/serial/by-path:
+lrwxrwxrwx 1 root root 13 Jan 22 20:26 platform-3f980000.usb-usb-0:1.4:1.0 -> ../../ttyACM0</code>
+    * Wenn nicht einfach mal USB raus und wieder rein und fertig ;-)
+===== Links =====
+  * https://mellow-3d.github.io/fly_adxl345_usb_general.html